DS109+

[Bigpapa]

Ik schrik van de reacties.
Dacht dat op wikipedia exact dezelfde processors waren.
Dan gaat ik dit niet doen. bedankt voor de info.

[Birdy]

Weet niet welke Wiki je hebt bekeken maar die van Synology klopt wel.

[Bigpapa]

Ik heb idd wel goed gekeken maar dacht dat de E niet zoveel kwaad kon.  Maar nu ik de reacties heb gekeken ben ik ook huiverig hiervoor geworden.

[pacecal]

@Hoststede

Ik heb zowel de serverip als de subnet gewijzigd, en toch blijft die hangen.

Code: [Selecteer]

DS109p>print
bootcmd=bootm FFC00000 FFE00000 FFF90000
bootdelay=2
baudrate=115200
loads_echo=1
ipaddr=192.168.1.78
serverip=192.168.1.77
rootpath=/nfsroot
gatewayip=192.168.1.1
netmask=255.255.0.0
hostname=DS109p
loadaddr=1000000
stdin=serial
stdout=serial
stderr=serial
bootargs=console=ttyS0,115200 ip=off initrd=0x00800000,4M root=/dev/sda1 rw syno_hw_version=DS109p ihd_num=0 netif_num=1
ethact=SK98#0
 
Environment size: 393/8188 bytes
DS109p>setenv serverip 192.168.1.14
DS109p>setenv netmask 255.255.255.0
DS109p>tftpboot 0x800000 rd.bin

Vraag 1. Moet je na de setenv nog iets doen? rebooten?

Probeer dan eens de ramdisk op een hoger of lager adres te laden. Als hij vastloopt is dat mogelijk een geheugenconflict.

Vraag 2. Hoe die ik dit? ramdisk wijzigen?

[Hofstede]

1. Nee, niet rebooten want dan ben je de environment wijzigingen weer kwijt omdat je ze niet opslaat.
2. Je kunt de ramdisk op een ander adres laden door het adres aan te passen.

Dus voor een lager adres bijvoorbeeld tftpboot 0x700000 rd.bin

Misschien is het ook handig om hier even een uitdraai van de output van de console te plaatsen. Dus gewoon even de NAS laten starten zonder onderbreking en dan alle output op de console even te loggen tot het moment dat hij vastloopt. Dat geeft mij mogelijk wat meer info wat er fout gaat. Tenslotte hoeft bij jou de ramdisk niet het probleem te zijn.

[pacecal]

Dus voor een lager adres bijvoorbeeld tftpboot 0x700000 rd.bin

Werkt niet, hier de output:

Code: [Selecteer]


Xshell 2.0 (Build 1512)
Copyright (c) 2003-2006 NetSarang Computer, Inc. All rights reserved.
 
Type `help' to learn how to use Xshell prompt.
Xshell:\>
Connecting to COM5...
Connected.
 
 
 
U-Boot 1.3.3 (Jan 27 2010 - 20:16:57)
 
CPU:   8533_E, Version: 1.1, (0x803c0011)
Core:  E500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU:1067 MHz, CCB: 534 MHz,
       DDR: 267 MHz (534 MT/s data rate), LBC:  33 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
I2C:   ready
DRAM:  Initializing
    DDR: 512 MB
FLASH:  4 MB
L2 cache 256KB: enabled
Using default environment
 
In:    serial
Out:   serial
Err:   serial
 
CPLD revision: 1.0
Synology Model: DS-109+
DRAM Type: DIMM
Fan Status: Good
 
Net:   SK98#0
Press Ctrl+C to abort autoboot in 2 second
## Booting image at ffc00000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1958771 Bytes =  1.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ffe00000 ...
   Image Name:   synology_ppc853x_110+ 3827
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    878751 Bytes = 858.2 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Booting using the fdt at 0xfff90000
   Loading Ramdisk to 1feb6000, end 1ff8c89f ... OK
   Loading Device Tree to 007fa000, end 007fcfff ... OK
[    0.000000] Using MPC8544 DS machine description
[    0.000000] Memory CAM mapping: 256/256/0/0 Mb, residual: 0Mb
[    0.000000] Linux version 2.6.32.12 (root@build1) (gcc version 3.4.3 20041021 (prerelease)) #3827 Tue Feb 11 19:54:37 CST 2014
[    0.000000] Found initrd at 0xbfeb6000:0xbff8c89f
[    0.000000] Found FSL PCI host bridge at 0x00000000e0008000. Firmware bus number: 0->255
[    0.000000] PCI host bridge /pci@e0008000  ranges:
[    0.000000]  MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[    0.000000]   IO 0x00000000e1000000..0x00000000e100ffff -> 0x0000000000000000
[    0.000000] /pci@e0008000: PCICSRBAR @ 0xfff00000
[    0.000000] Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->255
[    0.000000] PCI host bridge /pcie@e000a000  ranges:
[    0.000000]  MEM 0x00000000a0000000..0x00000000afffffff -> 0x00000000a0000000
[    0.000000]   IO 0x00000000e1020000..0x00000000e102ffff -> 0x0000000000000000
[    0.000000] /pcie@e000a000: PCICSRBAR @ 0xfff00000
[    0.000000] MPC85xx DS board from Freescale Semiconductor
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00020000
[    0.000000]   Normal   0x00020000 -> 0x00020000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00020000
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800000,4M root=/dev/sda1 rw syno_hw_version=DS109p ihd_num=0 netif_num=1
[    0.000000] Synology Hardware Version: DS109p-j
[    0.000000] Internal HD num: 0
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 513792k/524288k available (3912k kernel code, 9916k reserved, 200k data, 388k bss, 156k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xffffe000..0xfffff000  : fixmap
[    0.000000]   * 0xfdfdc000..0xfe000000  : early ioremap
[    0.000000]   * 0xc1000000..0xfdfdc000  : vmalloc & ioremap
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:512
[    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at e0040000, max 1 CPUs
[    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[    0.000000] mpic: Initializing for 256 sources
[    0.000000] clocksource: timebase mult[3c01894] shift[22] registered
[    0.000141] Mount-cache hash table entries: 512
[    0.000802] NET: Registered protocol family 16
[    0.001217] No RSTCR register, warm reboot won't work
[    0.001388] PCI: Probing PCI hardware
[    0.001594] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot
[    0.001601] pci 0000:00:0e.0: PME# disabled
[    0.001654] pci 0000:00:0e.1: PME# supported from D0 D1 D2 D3hot
[    0.001660] pci 0000:00:0e.1: PME# disabled
[    0.001741] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.001748] pci 0000:00:0f.0: PME# disabled
[    0.002338] pci 0001:01:00.0: ignoring class b20 (doesn't match header type 01)
[    0.002360] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.002367] pci 0001:01:00.0: PME# disabled
[    0.002939] pci 0001:01:00.0: BAR 9: can't allocate mem resource [0xb0000000-0xafffffff]
[    0.002948] pci 0001:01:00.0: PCI bridge, secondary bus 0001:02
[    0.002955] pci 0001:01:00.0:   IO window: 0x00-0xffff
[    0.002962] pci 0001:01:00.0:   MEM window: 0xa0000000-0xafffffff
[    0.002969] pci 0001:01:00.0:   PREFETCH window: disabled
[    0.002979] pci 0001:01:00.0: enabling device (0106 -> 0107)
[    0.006837] bio: create slab <bio-0> at 0
[    0.007444] SCSI subsystem initialized
[    0.007946] Switching to clocksource timebase
[    0.008733] NET: Registered protocol family 2
[    0.008796] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.008947] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.009139] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    0.009228] TCP: Hash tables configured (established 16384 bind 16384)
[    0.009234] TCP reno registered
[    0.009309] NET: Registered protocol family 1
[    0.009437] RPC: Registered udp transport module.
[    0.009444] RPC: Registered tcp transport module.
[    0.009449] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.009575] Trying to unpack rootfs image as initramfs...
[    0.742476] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    0.744162] Freeing initrd memory: 858k freed
[    0.745636] VFS: Disk quotas dquot_6.5.2
[    0.745660] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.746041] msgmni has been set to 1006
[    0.746120] alg: No test for md5 (md5-generic)
[    0.746161] alg: No test for des (des-generic)
[    0.746196] alg: No test for des3_ede (des3_ede-generic)
[    0.746232] alg: No test for stdrng (krng)
[    0.746351] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.746360] io scheduler noop registered
[    0.746365] io scheduler anticipatory registered (default)
[    0.811142] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.812358] serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 42) is a 16550A
[    1.300317] console [ttyS0] enabled
[    1.304310] serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 42) is a 16550A
[    1.314644] brd: module loaded
[    3.299012] scsi0 : sata_sil24
[    3.302302] scsi1 : sata_sil24
[    3.305490] ata1: SATA max UDMA/100 host m128@0xa0000000 port 0xa0004000 irq 18
[    3.312808] ata2: SATA max UDMA/100 host m128@0xa0000000 port 0xa0006000 irq 18
[    3.320115] Enable Synology sata fast booting
[    7.465381] physmap platform flash device: 00400000 at ffc00000
[    7.471545] SYNOMTD-0: Found 1 x16 devices at 0x0 in 8-bit bank
[    7.477469]  Amd/Fujitsu Extended Query Table at 0x0040
[    7.482708] SYNOMTD-0: Swapping erase regions for broken CFI table.
[    7.488974] number of CFI chips: 1
[    7.492370] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[    7.500130] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3b0000
[    7.560842] 6 RedBoot partitions found on MTD device SYNOMTD-0
[    7.566675] SYNOMTD flash bank 0: Using RedBoot partition definition
[    7.573028] Creating 6 MTD partitions on "SYNOMTD-0":
[    7.578078] 0x0000003c0000-0x000000400000 : "RedBoot"
[    7.583484] 0x000000000000-0x000000200000 : "zImage"
[    7.588729] 0x000000200000-0x000000380000 : "rd.gz"
[    7.593869] 0x000000380000-0x000000390000 : "vendor"
[    7.599224] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    7.605324] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    7.611414] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[    7.617505] serial number='A2F2N00047'
[    7.621078] 0x000000390000-0x0000003b0000 : "RedBoot Config"
[    7.627171] 0x0000003b0000-0x0000003c0000 : "FIS directory"
[    7.633025] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[    7.638950] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[    7.645053] md: raid1 personality registered for level 1
[    7.650437] TCP cubic registered
[    7.653666] NET: Registered protocol family 17
[    7.658119] NET: Registered protocol family 15
[    9.613994] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[    9.642609] ata1.00: ATA-9: WDC WD10EFRX-68PJCN0, 82.00A82, max UDMA/133
[    9.649313] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    9.656752] ata1.00: configured for UDMA/100
[    9.661604] scsi 0:0:0:0: Direct-Access     WDC      WD10EFRX-68PJCN0         82.0 PQ: 0 ANSI: 5
[    9.671026] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    9.678699] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    9.684134] sd 0:0:0:0: [sda] Write Protect is off
[    9.689002] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    9.698304]  sda: sda1 sda2 sda3
[    9.705871] sd 0:0:0:0: [sda] Attached SCSI disk
[   11.703977] ata2: SATA link down (SStatus 0 SControl 0)
[   11.709309] md: Waiting for all devices to be available before autodetect
[   11.716099] md: If you don't use raid, use raid=noautodetect
[   11.722048] md: Autodetecting RAID arrays.
[   11.726151] md: Scanned 0 and added 0 devices.
[   11.730589] md: autorun ...
[   11.733377] md: ... autorun DONE.
[   11.736751] RAMDISK: lzma image found at block 0
[   12.526122] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
[   12.609461] ppc85xx_synobios: module license 'Synology Inc.' taints kernel.
[   12.616429] Disabling lock debugging due to kernel taint
[   12.646124] correction with 0x0f
[   12.655585] synobios: load, major number 201
[   12.659858] Brand: Synology
[   12.662655] Model: DS-109+
[   12.665364] This is default settings: set group disks wakeup number to 1, spinup time deno 1
mknod: /dev/synobios: File exists
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[   12.687788] synobios: unload
Partition Version=7
 /sbin/e2fsck exists, checking /dev/hda1...
                                                                               
          12 inodes used (0.01%, out of 155648)
           0 non-contiguous files (0.0%)
           0 non-contiguous directories (0.0%)
             # of inodes with ind/dind/tind blocks: 0/0/0
             Extent depth histogram: 4
       27074 blocks used (4.35%, out of 622560)
           0 bad blocks
           1 large file
 
           1 regular file
           2 directories
           0 character device files
           0 block device files
           0 fifos
           0 links
           0 symbolic links (0 fast symbolic links)
           0 sockets
------------
           3 files
/sbin/e2fsck[   13.071345] EXT4-fs (sda1):  returns 0
Mounsynoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1ting /dev/hda1 /
tmpRoot
[   13.087556] EXT4-fs (sda1): barriers disabled
[   13.093372] EXT4-fs (sda1): mounted filesystem with ordered data mode
------------upgrade
use default /dev/hda3
Begin upgrade procedure
e2fsck 1.42.6 (21-Sep-2012)
Mount data partition
/bin/mount[   13.173383] EXT4-fs (sda3):  /dev/hda3 /tmpDsynoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1ata
 
[   13.201545] EXT4-fs (sda3): barriers disabled
[   13.695711] EXT4-fs (sda3): mounted filesystem with ordered data mode
No upgrade file exists
[   13.747179] synoacl module [synoacl_ext4] is not loaded
[   13.752498] synoacl module [synoacl_vfs] is not loaded
End upgrade procedure
============upgrade
Copy default /etc
cp: can't stat '/tmpRoot/etc.defaults': No such file or directory
Copy default /usr/syno/etc
cp: can't stat '/tmpRoot/usr/syno/etc.defaults': No such file or directory
Copy default /var
cp: can't stat '/t[   13.781461] synoacl module [synoacl_ext4] is not loaded
mpRoot/var.defau[   13.787904] synoacl module [synoacl_vfs] is not loaded
lts': No such file or directory
Exit on error [2] .noroot exists...
/dev/hda1 /tmpRoot ext4 rw,relatime,nosynoacl,barrier=0,journal_checksum,data=ordered 0 0
none /sys sysfs rw,relatime 0 0
linuxrc.syno failed on 2
rm: /etc: is a directory
starting pid 900, tty '': '/etc/rc'
:: Starting /etc/rc
/etc/rc: line 52: /usr/syno/bin/synoplatform: not found
:: Prepare var ... [  OK  ]
:: Mounting procfs ... [  OK  ]
:: Mounting tmpfs ... [  OK  ]
:: Mounting devpts ... [  OK  ]
:: Mounting sysfs ... [  OK  ]
:: Checking new disks ...
No new disk. Do nothing.
[   13.917274] Adding 2097144k swap on /dev/hda2.  Priority:-1 extents:1 across:2097144k
/dev/root.old on / type ext2 (rw,relatime,errors=continue)
/tmp on /tmp type tmpfs (0)
none on /dev/pts type devpts (gid=4,mode=620)
/sys on /sys type sysfs (0)
:: Loading module usbcore[   14.049861] usbcore: registered new interface driver usbfs
[   14.072595] usbcore: registered new interface driver hub
[   14.088377] usbcore: registered new device driver usb
 ... [  OK  ]
:: Loading module i2c-core ... [  OK  ]
:: Loading module of_i2c ... [  OK  ]
:: Loading module i2c-mpc ... [  OK  ]
:: Loading module fat ... [  OK  ]
:: Loading module vfat ... [  OK  ]
:: Mounting usbfs ... [  OK  ]
:: Loading module skge[   14.341936] skge 0000:00:0f.0: enabling device (0006 -> 0007)
[   14.347741] skge 1.13 addr 0xc0004000 irq 17 chip Yukon-Lite rev 9
[   14.353927] skge 0000:00:0f.0: bad (zero?) ethernet address in rom
[   14.373080] skge eth0: addr 00:00:00:00:00:00
 ... [  OK  ]
:: Loading module synobios[   14.420429] correction with 0x0f
[   14.431134] synobios: load, major number 201
[   14.435410] Brand: Synology
[   14.438207] Model: DS-109+
[   14.440913] This is default settings: set group disks wakeup number to 1, spinup time deno 1
 ... [  OK  ]
[   14.576270] skge eth0: enabling interface
udhcpc (v1.16.1) started
eth0      Link encap:Ethernet  HWaddr 00:11:32:06:32:2F 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17
 
lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
 
ls: /etc/dhcpd/dhcpd-*.conf: No such file or directory
ls: /etc/dhcpd/dhcpd-*.info: No such file or directory
grep: /etc/dhcpd/dhcpd.info: No such file or directory
/etc/rc: line 456: /sbin/sysctl: not found
:: Starting syslogd ... [  OK  ]
/etc/rc: line 523: /usr/syno/etc/rc.d/S98findhostd.sh: not found
/etc.defaults/rc.volume: line 231: awk: not found
/etc.defaults/rc.volume: line 231: /usr/syno/bin/synoarchiveupgrade: not found
/etc/rc: line 537: /usr/syno/bin/synokerneltz: not found
/etc/rc: line 539: /sbin/sysctl: not found
/etc/rc: line 545: /sbin/sysctl: not found
/etc/rc: line 557: awk: not found
/etc/rc: line 557: /sbin/sysctl: not found
/etc/rc: line 588: /usr/syno/bin/synologset1: not found
:: Starting scemd
:: Starting services in background
/etc/rc: line 630: sort: not found
/etc/rc: line 630: sed: not found
/etc/rc: line 630: servicetool: not found
/etc/rc.network: line 1396: awk: not found
Starting findhostd in flash_rd...
Starting services in flash_rd...
Running /usr/syno/etc/rc.d/J80ADTFanControl.sh...
[   21.995119] EXT4-fs (sda3): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[   22.023906] EXT4-fs (sda3): barriers disabled
[   22.520199] EXT4-fs (sda3): mounted filesystem with ordered data mode
:: Loading module ehci-hcd[   22.540392] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   22.546997] ehci_hcd 0000:00:0e.1: EHCI Host Controller
[   22.552264] ehci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 1
[   22.559701] ehci_hcd 0000:00:0e.1: Enabling legacy PCI PM
[   22.585181] synoacl module [synoacl_ext4] is not loaded
[   22.590506] synoacl module [synoacl_vfs] is not loaded
[   22.595799] ehci_hcd 0000:00:0e.1: irq 16, io mem 0xc0001000
[   22.606975] ehci_hcd 0000:00:0e.1: USB 2.0 started, EHCI 1.00
[   22.613267] usb usb1: configuration #1 chosen from 1 choice
[   22.619364] EXT4-fs (sda1): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[   22.631878] EXT4-fs (sda1): barriers disabled
[   22.644354] EXT4-fs (sda1): mounted filesystem with ordered data mode
[   22.654003] hub 1-0:1.0: USB hub found
[   22.657789] hub 1-0:1.0: 3 ports detected
[   22.671555] synoacl module [synoacl_ext4] is not loaded
[   22.676884] synoacl module [synoacl_vfs] is not loaded
[   22.689323] EXT4-fs (sda3): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[   22.721490] EXT4-fs (sda3): barriers disabled
[   23.220440] EXT4-fs (sda3): mounted filesystem with ordered data mode
 ... [  OK  ]
:: Loading module ohci-hcd[   23.253013] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   23.259250] ohci_hcd 0000:00:0e.0: OHCI Host Controller
[   23.264500] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
[   23.271918] ohci_hcd 0000:00:0e.0: irq 16, io mem 0xc0000000
[   23.299181] synoacl module [synoacl_ext4] is not loaded
[   23.304506] synoacl module [synoacl_vfs] is not loaded
[   23.330371] usb usb2: configuration #1 chosen from 1 choice
[   23.339682] hub 2-0:1.0: USB hub found
[   23.343475] hub 2-0:1.0: 3 ports detected
 ... [  OK  ]
:: Loading module usb-storage[   23.412984] Initializing USB Mass Storage driver...
[   23.420439] usbcore: registered new interface driver usb-storage
[   23.426466] USB Mass Storage support registered.
 ... [  OK  ]
startup daemons
Sat Dec 27 09:50:43 UTC 2014
/etc/rc: line 740: /sbin/initctl: not f
DiskStation login:



[Hofstede]

Hij heeft dus duidelijk de ramdisk voor een 110+ geladen.

Wat gebeurt er als je alleen tftpboot intypt, zonder parameters. Krijg je dan een foutmelding? Of loopt hij dan ook vast?

[pacecal]

ook een vastloper...

[Hofstede]

Ok. Werkt het tftp commando?

Dus: tftp adres filenaam?

[pacecal]

Dus, tftp 192.168.1.14 rd.bin?

[Hofstede]

Nee, geheugenadres. Dus tftp 0x700000 rd.bin. Of probeer ook eerst alleen tftp.

[pacecal]

werkt allemaal niet, telkens een vastloper...

[pacecal]

Kan het te maken hebben met een firewall? of iets anders wat de connectie tegen houd?


Wat krijg je normaal als je tftp intikt dan?

[Hofstede]

Normaal gesproken krijg je dan een overzicht van de mogelijke opties. Het lijkt er op dat hij vastloopt op het ethernet deel. Dat werkt dus niet goed lijkt het. Werkt het ping commando? Dus bijvoorbeeld ping <ip adres van tftp server> .

[pacecal]

Het IP-adres van de tftpserver is gelijk aan die van mijn laptop. De instructie Ping komt volgens mij niet voor in de putty console.


Ik kan wel buiten Putty in een dosbox verbinding maken met de tftp server: tftp 192.168.1.14 get rs.bin. Dit werkt prima.