DS109+

[Hofstede]

Daar ging het mij niet om. Het lijkt er op dat het netwerk niet goed werkt. De volgende optie zou zijn om de rd.bin file via de seriële verbinding naar de NAS te uploaden. Kijk eens of het loadb commando werkt.

[pacecal]

Deze instructie werkt wel: ik krijg de melding:

## Ready for binary (kermit) download to 0x01000000 at 115200 bps...

[Hofstede]

Ok. Dan moet je dit commando gebruiken. Dus bijvoorbeeld loadb 0x800000. En dan vanaf de PC de rd.bin file uploaden met een terminal programma dat het kermit protocol ondersteund.

[Birdy]

Ho eens, kermit  Das lang geleden, heb ergens nog een boek van liggen, geloof ik. 
Volledig off topic natuurlijk 

[Hofstede]

@Birdy: Ja, de basis blijft nog altijd hetzelfde. Gelukkig zijn we (nog) niet op machinetaal-niveau. Het is wel lastig om @pacecal op deze wijze te helpen. Als ik zelf hands-on met de machine zou zijn zou het veel sneller gaan. Maar gelukkig heeft @pacecal er lol aan

[pacecal]

   Ik vind het zonde om de handdoek in de ring te gooien, ook al heb ik inmiddels een nieuwe.


Nog even wat gedachtenspinsels;


Op 2 verschillende laptops werkt tftp niet, kan dit te maken hebben met het feit dat de rode draad niet zit aangesloten?

[Hofstede]

Nee, tftp werkt alleen met het netwerk. Heeft dus niks met de seriële kabel te maken. Op de een of andere manier loopt je netwerkinterface vast zodra je die met een netwerkcommando benaderd. Daarom zul je nu op serieel niveau moeten werken. Je werkt nu meen ik met Vista? Daarop staat volgens mij nog HyperTerminal. Die kan volgens mij file overdracht via Kermit protocol aan.

[Birdy]

Daarop staat volgens mij nog HyperTerminal. Die kan volgens mij file overdracht via Kermit protocol aan.

Volgens mij is HyperTerminal sinds Vista verwijderd door MS.

Mogelijk alternatief is TeraTerm, die ondersteunt Kermit.
http://en.sourceforge.jp/projects/ttssh2/releases/

Edit:

System Requirements: Operating System: Windows 7, Windows 95/98/ME, Windows NT/2000

Lijkt mij sterk dat het niet op Vista zou kunnen draaien.

[pacecal]

Ik heb het volgende gedaan:

- Via Putty Extra het commando loadY gegegeven;
- Via Putty Extra de instructie File Transfer / Ymodem / Receive het bestand [rd.bin] succesvol overgebracht;
- Via Putty Extra het commando bootm FFC00000 800000 FFF90000 gegeven, toen liep die weer vast met een oranje knipperend lampje...

[Hofstede]

Was 800000 ook het adres waarop de Ramdisk was geladen?

Het kan zijn dat je de bijbehorende Linux shell uit de firmware file ook moet laden. En dan moet je booten met die Linux shell en ramdisk image in RAM.

[pacecal]

het adres was 1000000, maar dan blijft die ook hangen. Ik denk idd dat ik dan ook de zImage moet laden. Ik heb wel dan een andere uitdaging. Het adres 100000 genereert die automatisch, hoe kan ik dan op een tweede adres een ander bestand laden?

[Hofstede]

Je moet by het commando loady het adres meegeven. Dus bijvoorbeeld  loady 0x800000. Let ook op dat je voor adressen 0x zet. 0x100000 is iets anders dan 100000.

[pacecal]

Okej, ik heb het volgende nu gedaan:

- Sluit de kabel aan exclusief de rode;
- Gebruik Putty Extra om via Serial (com-poort) verbinding te maken met je NAS: 115200;
- Zorg er voor dat de bestanden zImage en rb.bin uitgepakt zijn uit de firmware (.pat);
- Gebruik de onderstaande instructies om beiden bestanden in het geheugen te laden;
- loady 0x1000000;
- Ga nu via het menu naar Transfer File / Ymodem / Reveive file en selecteer zImage;
- Even wachten...
- loady 0x800000;
- Ga nu via het menu naar Transfer File / Ymodem / Reveive file en selecteer rd.bin;
- Even wachten...
- Gebruik de laatste instructie: bootm 1000000 800000 FFF90000

Bron: http://www.synology-forum.de/showthread.html?47593-DS109-bootet-nicht-mehr

Gezien ik nu beide adressen op de juiste manier heb geladen en aangeroepen hoopte ik dat hij het zou doen. Helaas, ik krijg weer een oranje knipperend lampje. Hier nog even de volledige instructie.

Wijzigingen:

DS109p>loady 0x01000000 (zImage)
## Ready for binary (ymodem) download to 0x01000000 at 115200 bps...
CCCxyzModem - CRC mode, 1(SOH)/1876(STX)/0(CAN) packets, 5 retries
## Total Size      = 0x001d4f07 = 1920775 Bytes
DS109p>loady 0x800000 (rd.bin)
## Ready for binary (ymodem) download to 0x00800000 at 115200 bps...
CCCCCxyzModem - CRC mode, 1(SOH)/708(STX)/0(CAN) packets, 7 retries
## Total Size      = 0x000b0cbe = 724158 Bytes
DS109p>bootm 1000000 800000 FFF90000

Bootproces:

Code: [Selecteer]

## Booting image at 01000000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1920711 Bytes =  1.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00800000 ...
   Image Name:   synology_ppc853x_109+ 3252
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    724094 Bytes = 707.1 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Booting using the fdt at 0xfff90000
   Loading Ramdisk to 1fedc000, end 1ff8cc7e ... OK
   Loading Device Tree to 007fa000, end 007fcfff ... OK
[    0.000000] Using MPC8544 DS machine description
[    0.000000] Memory CAM mapping: 256/256/0/0 Mb, residual: 0Mb
[    0.000000] Linux version 2.6.32.12 (root@build3) (gcc version 3.4.3 20041021 (prerelease)) #3252 Thu Sep 4 13:54:10 CST 2014
[    0.000000] Found initrd at 0xbfedc000:0xbff8cc7e
[    0.000000] Found FSL PCI host bridge at 0x00000000e0008000. Firmware bus number: 0->255
[    0.000000] PCI host bridge /pci@e0008000  ranges:
[    0.000000]  MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[    0.000000]   IO 0x00000000e1000000..0x00000000e100ffff -> 0x0000000000000000
[    0.000000] /pci@e0008000: PCICSRBAR @ 0xfff00000
[    0.000000] Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->255
[    0.000000] PCI host bridge /pcie@e000a000  ranges:
[    0.000000]  MEM 0x00000000a0000000..0x00000000afffffff -> 0x00000000a0000000
[    0.000000]   IO 0x00000000e1020000..0x00000000e102ffff -> 0x0000000000000000
[    0.000000] /pcie@e000a000: PCICSRBAR @ 0xfff00000
[    0.000000] MPC85xx DS board from Freescale Semiconductor
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00020000
[    0.000000]   Normal   0x00020000 -> 0x00020000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00020000
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800000,4M root=/dev/sda1 rw syno_hw_version=DS109p ihd_num=0 netif_num=1
[    0.000000] Synology Hardware Version: DS109p-j
[    0.000000] Internal HD num: 0
[    0.000000] Internal netif num: 1
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 514048k/524288k available (3836k kernel code, 9700k reserved, 196k data, 404k bss, 152k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xffffe000..0xfffff000  : fixmap
[    0.000000]   * 0xfdfdc000..0xfe000000  : early ioremap
[    0.000000]   * 0xc1000000..0xfdfdc000  : vmalloc & ioremap
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:512
[    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at e0040000, max 1 CPUs
[    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[    0.000000] mpic: Initializing for 256 sources
[    0.000000] clocksource: timebase mult[3c01894] shift[22] registered
[  451.016810] Mount-cache hash table entries: 512
[  451.017462] NET: Registered protocol family 16
[  451.017876] No RSTCR register, warm reboot won't work
[  451.018047] PCI: Probing PCI hardware
[  451.018255] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot
[  451.018262] pci 0000:00:0e.0: PME# disabled
[  451.018315] pci 0000:00:0e.1: PME# supported from D0 D1 D2 D3hot
[  451.018322] pci 0000:00:0e.1: PME# disabled
[  451.018402] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[  451.018409] pci 0000:00:0f.0: PME# disabled
[  451.019003] pci 0001:01:00.0: ignoring class b20 (doesn't match header type 01)
[  451.019025] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[  451.019032] pci 0001:01:00.0: PME# disabled
[  451.019603] pci 0001:01:00.0: BAR 9: can't allocate mem resource [0xb0000000-0xafffffff]
[  451.019612] pci 0001:01:00.0: PCI bridge, secondary bus 0001:02
[  451.019619] pci 0001:01:00.0:   IO window: 0x00-0xffff
[  451.019626] pci 0001:01:00.0:   MEM window: 0xa0000000-0xafffffff
[  451.019633] pci 0001:01:00.0:   PREFETCH window: disabled
[  451.019643] pci 0001:01:00.0: enabling device (0106 -> 0107)
[  451.023491] bio: create slab <bio-0> at 0
[  451.024099] SCSI subsystem initialized
[  451.024598] Switching to clocksource timebase
[  451.025384] NET: Registered protocol family 2
[  451.025445] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[  451.025573] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[  451.025766] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[  451.025854] TCP: Hash tables configured (established 16384 bind 16384)
[  451.025861] TCP reno registered
[  451.025934] NET: Registered protocol family 1
[  451.026063] RPC: Registered udp transport module.
[  451.026070] RPC: Registered tcp transport module.
[  451.026075] RPC: Registered tcp NFSv4.1 backchannel transport module.
[  451.026205] Trying to unpack rootfs image as initramfs...
[  451.695436] rootfs image is not initramfs (no cpio magic); looks like an initrd
[  451.696790] Freeing initrd memory: 707k freed
[  451.698241] VFS: Disk quotas dquot_6.5.2
[  451.698265] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[  451.698603] msgmni has been set to 1006
[  451.698732] alg: No test for md5 (md5-generic)
[  451.698774] alg: No test for des (des-generic)
[  451.698809] alg: No test for des3_ede (des3_ede-generic)
[  451.698845] alg: No test for stdrng (krng)
[  451.698962] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[  451.698971] io scheduler noop registered
[  451.698977] io scheduler anticipatory registered (default)
[  451.763427] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[  451.764697] serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 42) is a 16550A
[  452.252551] console [ttyS0] enabled
[  452.256545] serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 42) is a 16550A
[  452.266920] brd: module loaded
[  452.270980] scsi0 : sata_sil24
[  452.274308] scsi1 : sata_sil24
[  452.277490] ata1: SATA max UDMA/100 host m128@0xa0000000 port 0xa0004000 irq 18
[  452.284815] ata2: SATA max UDMA/100 host m128@0xa0000000 port 0xa0006000 irq 18
[  452.292121] Enable Synology sata fast booting
[  456.437039] physmap platform flash device: 00400000 at ffc00000
[  456.443205] SYNOMTD-0: Found 1 x16 devices at 0x0 in 8-bit bank
[  456.449128]  Amd/Fujitsu Extended Query Table at 0x0040
[  456.454367] SYNOMTD-0: Swapping erase regions for broken CFI table.
[  456.460633] number of CFI chips: 1
[  456.464030] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
[  456.471789] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3b0000
[  456.532504] 6 RedBoot partitions found on MTD device SYNOMTD-0
[  456.538337] SYNOMTD flash bank 0: Using RedBoot partition definition
[  456.544691] Creating 6 MTD partitions on "SYNOMTD-0":
[  456.549741] 0x0000003c0000-0x000000400000 : "RedBoot"
[  456.555151] 0x000000000000-0x000000200000 : "zImage"
[  456.560398] 0x000000200000-0x000000380000 : "rd.gz"
[  456.565542] 0x000000380000-0x000000390000 : "vendor"
[  456.570890] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[  456.576997] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[  456.583087] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0.
[  456.589178] serial number='A2F2N00047'
[  456.592752] 0x000000390000-0x0000003b0000 : "RedBoot Config"
[  456.598840] 0x0000003b0000-0x0000003c0000 : "FIS directory"
[  456.604704] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[  456.610633] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[  456.616738] md: raid1 personality registered for level 1
[  456.622096] TCP cubic registered
[  456.625322] NET: Registered protocol family 17
[  458.585645] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[  458.592130] ata1.00: ATA-9: WDC WD10EFRX-68PJCN0, 82.00A82, max UDMA/133
[  458.598834] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[  458.606207] ata1.00: configured for UDMA/100
[  458.610651] scsi 0:0:0:0: Direct-Access     WDC      WD10EFRX-68PJCN0 82.0 PQ: 0 ANSI: 5
[  458.619362] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[  458.627032] sd 0:0:0:0: [sda] 4096-byte physical blocks
[  458.632478] sd 0:0:0:0: [sda] Write Protect is off
[  458.637345] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  458.646682]  sda: sda1 sda2 sda3
[  459.259739] sd 0:0:0:0: [sda] Attached SCSI disk
[  460.651629] ata2: SATA link down (SStatus 0 SControl 0)
[  460.656908] md: Waiting for all devices to be available before autodetect
[  460.663697] md: If you don't use raid, use raid=noautodetect
[  460.669640] md: Autodetecting RAID arrays.
[  460.673736] md: Scanned 0 and added 0 devices.
[  460.678173] md: autorun ...
[  460.680961] md: ... autorun DONE.
[  460.684334] RAMDISK: lzma image found at block 0
[  461.410600] VFS: Mounted root (ext2 filesystem) on device 1:0.
START /linuxrc.syno
[  461.495666] ppc85xx_synobios: module license 'Synology Inc.' taints kernel.
[  461.502633] Disabling lock debugging due to kernel taint
[  461.530323] correction with 0x0f
[  461.539773] synobios: load, major number 201
[  461.544046] Brand: Synology
[  461.546843] Model: DS-109+
[  461.549549] This is default settings: set group disks wakeup number to 1, spinup time deno 1
mknod: /dev/synobios: File exists
Starting /usr/syno/bin/synocfgen...
/usr/syno/bin/synocfgen returns 0
[  461.571572] synobios: unload
rmmod: can't unload 'i2c_core': Resource temporarily unavailable
Partition Version=7
 /sbin/e2fsck exists, checking /dev/hda1...

      12 inodes used (0.01%)
       0 non-contiguous files (0.0%)
       0 non-contiguous directories (0.0%)
         # of inodes with ind/dind/tind blocks: 0/0/0
         Extent depth histogram: 4
   27074 blocks used (4.35%)
       0 bad blocks
       1 large file

       1 regular file
       2 directories
       0 character device fil[  461.858575] EXT4-fs (sda1): es
       0 blosynoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1ck device files

[  461.874521] EXT4-fs (sda1):
barriers disabled                     0 links
                        0 symbol
ic links (0 fast[  461.883738] EXT4-fs (sda1):  symbolic links)mounted filesystem with ordered data mode
       0 socke
ts
--------
       3 files
/sbin/e2fsck returns 0
Mounting /dev/hda1 /tmpRoot
------------upgrade
use default /dev/hda3
Begin upgrade procedure
e2fsck 1.41.12 (17-May-2010)
Mount data partition
/bin/mount /dev/hda3 /tmpData
[  462.193505] EXT4-fs (sda3): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[  462.219094] EXT4-fs (sda3): barriers disabled
[  462.713293] EXT4-fs (sda3): mounted filesystem with ordered data mode
No upgrade file exists
[  462.756834] synoacl module [synoacl_ext4] is not loaded
[  462.762153] synoacl module [synoacl_vfs] is not loaded
End upgrade procedure
============upgrade
Copy default /etc
cp: can't stat '/tmpRoot/etc.defaults': No such file or directory
Copy default /usr/syno/etc
cp: can't stat '/tmpRoot/usr/syno/etc.defaults': No such file or directory
Copy default /var
cp: can't stat '/t[  462.791123] synoacl module [synoacl_ext4] is not loaded
mpRoot/var.defau[  462.797579] synoacl module [synoacl_vfs] is not loaded
lts': No such file or directory
Exit on error [2] .noroot exists...
/dev/hda1 /tmpRoot ext4 rw,relatime,nosynoacl,barrier=0,journal_checksum,data=ordered 0 0
none /sys sysfs rw,relatime 0 0
linuxrc.syno failed on 2
rm: /etc: is a directory
starting pid 897, tty '': '/etc/rc'
:: Starting /etc/rc
/etc/rc: line 52: /usr/syno/bin/synoplatform: not found
:: Prepare var [OK]
:: Mounting procfs [OK]
:: Mounting tmpfs [OK]
:: Mounting devpts [OK]
:: Mounting sysfs [OK]
:: Checking new disks ...
No new disk. Do nothing.
[  462.904492] Adding 2097144k swap on /dev/hda2.  Priority:-1 extents:1 across:2097144k
/dev/root.old on / type ext2 (rw,relatime,errors=continue)
/tmp on /tmp type tmpfs (0)
none on /dev/pts type devpts (gid=4,mode=620)
/sys on /sys type sysfs (0)
Hostname DiskStation
:: Loading module i2c-core [OK]
:: Loading module of_i2c [OK]
:: Loading module i2c-mpc [OK]
:: Mounting usbfs [FAILED]
:: Loading module skge[  463.141860] skge 0000:00:0f.0: enabling device (0006 -> 0007)
[  463.147662] skge 1.13 addr 0xc0004000 irq 17 chip Yukon-Lite rev 9
[  463.153850] skge 0000:00:0f.0: bad (zero?) ethernet address in rom
[  463.173006] skge eth0: addr 00:00:00:00:00:00
 [OK]
:: Loading module synobios[  463.237649] correction with 0x0f
[  463.248288] synobios: load, major number 201
[  463.252565] Brand: Synology
[  463.255362] Model: DS-109+
[  463.258071] This is default settings: set group disks wakeup number to 1, spinup time deno 1
 [OK]
[  463.384599] skge eth0: enabling interface
udhcpc (v1.16.1) started
eth0      Link encap:Ethernet  HWaddr 00:11:32:06:32:2F
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:17

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ls: /etc/dhcpd/dhcpd-*.conf: No such file or directory
ls: /etc/dhcpd/dhcpd-*.info: No such file or directory
grep: /etc/dhcpd/dhcpd.info: No such file or directory
/etc/rc: line 407: /sbin/sysctl: not found
:: Starting syslogd [OK]
/etc/rc: line 476: /usr/syno/etc/rc.d/S98findhostd.sh: not found
/etc.defaults/rc.volume: line 221: awk: not found
/etc.defaults/rc.volume: line 221: /usr/syno/bin/synoarchiveupgrade: not found
/etc/rc: line 490: /usr/syno/bin/synokerneltz: not found
/etc/rc: line 492: /sbin/sysctl: not found
/etc/rc: line 498: /sbin/sysctl: not found
/etc/rc: line 510: awk: not found
/etc/rc: line 510: /sbin/sysctl: not found
/etc/rc: line 541: /usr/syno/bin/synologset1: not found
:: Starting scemd
:: Starting services in background
/etc/rc: line 587: sort: not found
/etc/rc: line 587: sed: not found
/etc/rc: line 587: servicetool: not found
/etc/rc.network: line 1357: awk: not found
Starting findhostd in flash_rd...
Starting services in flash_rd...
[  470.793380] EXT4-fs (sda3): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[  470.820845] EXT4-fs (sda3): barriers disabled
[  471.317524] EXT4-fs (sda3): mounted filesystem with ordered data mode
startup daemons
Tue Dec 30 11:59:54 UTC 2014
starting pid 1563, tty '': '/sb[  471.356836] synoacl module [synoacl_ext4] is not loaded
[  471.362160] synoacl module [synoacl_vfs] is not loaded
[  471.380565] EXT4-fs (sda1): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[  471.393048] EXT4-fs (sda1): barriers disabled
[  471.409205] EXT4-fs (sda1): mounted filesystem with ordered data mode
[  471.424837] synoacl module [synoacl_ext4] is not loaded
[  471.430161] synoacl module [synoacl_vfs] is not loaded
[  471.438244] EXT4-fs (sda3): synoacl module has not been loaded. Unable to mount with synoacl, vfs_mod status=-1, ext4_mod status=-1
[  471.463865] EXT4-fs (sda3): barriers disabled
[  471.958070] EXT4-fs (sda3): mounted filesystem with ordered data mode
[  471.977866] synoacl module [synoacl_ext4] is not loaded
[  471.983190] synoacl module [synoacl_vfs] is not loaded

DiskStation login: root


[Hofstede]

Je gebruikt nu vreemde adressen, en het bootadres FFF90000 klopt zo niet  . Je start nog steeds vanuit de flash.


Begin even opnieuw.


Laad zImage op 0x600000
Laad rd.bin op 0x800000


Dan bootm 600000 800000 9f0000


Ook lijkt het er op dat de NAS in de war raakt door de oude gedeeltelijk geupgrade DSM info op je schijf. Probeer het anders eens zonder of met een lege schijf.

[pacecal]

Met en zonder HD blijft die hangen:

Code: [Selecteer]

DS109p>loady 0x600000
## Ready for binary (ymodem) download to 0x00600000 at 115200 bps...
CCxyzModem - CRC mode, 1(SOH)/1876(STX)/0(CAN) packets, 4 retries
## Total Size      = 0x001d4f07 = 1920775 Bytes
DS109p>loady 0x800000
## Ready for binary (ymodem) download to 0x00800000 at 115200 bps...
CCxyzModem - CRC mode, 1(SOH)/708(STX)/0(CAN) packets, 4 retries
## Total Size      = 0x000b0cbe = 724158 Bytes
DS109p>bootm 600000 800000 9f0000
## Booting image at 00600000 ...
   Image Name:   Linux-2.6.32.12
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1920711 Bytes =  1.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00800000 ...
   Image Name:   synology_ppc853x_109+ 3252
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    724094 Bytes = 707.1 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Booting using the fdt at 0x9f0000
   Loading Ramdisk to 1fedc000, end 1ff8cc7e ... OK
   Loading Device Tree to 007fd000, end 007fcffe ...